View MC33502_159272.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Order this document by MC33502/D
Advance Information
One Volt SMARTMOSTM Rail-to-Rail Dual Operational Amplifier
The MC33502 operational amplifier provides rail-to-rail operation on both the input and output. The output can swing within 50 mV of each rail. This rail-to-rail operation enables the user to make full use of the entire supply voltage range available. It is designed to work at very low supply voltages (1.0 V and ground), yet can operate with a supply of up to 7.0 V and ground. Output current boosting techniques provide high output current capability while keeping the drain current of the amplifier to a minimum. * Low Voltage, Single Supply Operation (1.0 V and Ground to 7.0 V and Ground) * High Input Impedance: Typically 40 fA Input Current
MC33502
LOW VOLTAGE RAIL-TO-RAIL DUAL OPERATIONAL AMPLIFIER
SEMICONDUCTOR TECHNICAL DATA
* * * * * * * * * * * * * * * * * * *
Typical Unity Gain Bandwidth @ 5.0 V = 5.0 MHz, @ 1.0 V = 4.0 MHz High Output Current (ISC = 50 mA @ 5.0 V, 10 mA @ 1.0 V) Output Voltage Swings within 50 mV of Both Rails @ 1.0 V Input Voltage Range Includes Both Supply Rails High Voltage Gain: 100 dB Typical @ 1.0 V No Phase Reversal on the Output for Over-Driven Input Signals Input Offset Trimmed to 0.5 mV Typical Low Supply Current (ID = 1.2 mA/per Amplifier, Typical) 600 Drive Capability Extended Operating Temperature Range (-40 to 105C)
8 1 8 1
P SUFFIX PLASTIC PACKAGE CASE 626
APPLICATIONS
Single Cell NiCd/Ni MH Powered Systems Interface to DSP Portable Communication Devices Low Voltage Active Filters Telephone Circuits Instrumentation Amplifiers Audio Applications Power Supply Monitor and Control Compatible with VCX Logic
Output 1 1
D SUFFIX PLASTIC PACKAGE CASE 751 (SO-8)
PIN CONNECTIONS
8 VCC 7 Output 2 1 2 6 5 (Dual, Top View) Inputs 2
Simplified Block Diagram
Inputs 1 Base Current Boost Inputs Input Stage Buffer with 0 V Level Shift Saturation Detector Outputs
2 3 VEE 4
Output Stage
ORDERING INFORMATION
Base Current Boost Device MC33502P Operating Temperature Range TA = - 40 to +105C Package Plastic DIP SO-8
Rev 0
Offset Voltage Trim
This device contains 98 active transistors per amplifier.
This document contains information on a new product. Specifications and information herein are subject to change without notice.
MC33502D
(c) Motorola, Inc. 1998
MOTOROLA ANALOG IC DEVICE DATA
1
MC33502
MAXIMUM RATINGS
AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A
AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A
AAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A AA AAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAA A AA
Supply Voltage (VCC to VEE) VS 7.0 V V V V V s ESD Protection Voltage at any Pin H man Bod Model Human Body Voltage at Any Device Pin VESD VDP 2000 VS 0.3 Input Differential Voltage Range VIDR VCM tS VCC to VEE VCC to VEE (Note 1) 150 Common Mode Input Voltage Range Output Short Circuit Duration Maximum Junction Temperature Storage Temperature Range TJ C C Tstg PD -65 to 150 (Note 1) Maximum Power Dissipation mW
NOTES: 1. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. 2. ESD data available upon request.
Rating
Symbol
Value
Unit
DC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, RL to VCC/2, TA = 25C, unless
otherwise noted.) Characteristic Symbol VIO Min Typ Max Unit mV
Input Offset Voltage (VCM = 0 to VCC) VCC = 1.0 V TA = 25C TA = -40 to 105C VCC = 3.0 V TA = 25C TA = -40 to 105C VCC = 5.0 V TA = 25C TA = -40 to 105C
-5.0 -7.0 -5.0 -7.0 -5.0 -7.0 - -
0.5 - 0.5 - 0.5 - 8.0 40 -
5.0 7.0 5.0 7.0 5.0 7.0 - -
Input Offset Voltage Temperature Coefficient (RS = 50 ) TA = -40 to 105C Input Bias Current (VCC = 1.0 to 5.0 V) Common Mode Input Voltage Range Large Signal Voltage Gain VCC = 1.0 V (TA = 25C) RL = 10 k RL = 1.0 k VCC = 3.0 V (TA = 25C) RL = 10 k RL = 1.0 k VCC = 5.0 V (TA = 25C) RL = 10 k RL = 1.0 k
VIO/T I IIB I
V/C fA V
VICR
VEE
VCC
AVOL
kV/V
25 5.0 50 25 50 25
100 50 500 100 500 200
- - - - - -
2
MOTOROLA ANALOG IC DEVICE DATA
MC33502
DC ELECTRICAL CHARACTERISTICS (continued) (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, RL to VCC/2, TA = 25C, unless
otherwise noted.) Characteristic Output Voltage Swing, High (VID = 0.2 V) VCC = 1.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 1.0 V (TA = -40 to 105C) RL = 10 k RL = 600 VCC = 3.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 3.0 V (TA = -40 to 105C) RL = 10 k RL = 600 VCC = 5.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 5.0 V (TA = -40 to 105C) RL = 10 k RL = 600 Output Voltage Swing, Low (VID = 0.2 V) VCC = 1.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 1.0 V (TA = -40 to 105C) RL = 10 k RL = 600 VCC = 3.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 3.0 V (TA = -40 to 105C) RL = 10 k RL = 600 VCC = 5.0 V (TA = 25C) RL = 10 k RL = 600 VCC = 5.0 V (TA = -40 to 105C) RL = 10 k RL = 600 Symbol VOH Min Typ Max Unit V
AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A
0.9 0.85 0.85 0.8 2.9 2.8 2.85 2.75 4.9 4.75 4.85 4.7 0.95 0.88 - - 2.93 2.84 - - 4.92 4.81 - - - - - - - - - - - - - -
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A
VOL V 0.05 0.1 0.1 0.15 0.05 0.1 0.1 0.15 0.05 0.15 0.1 0.2 CMR VOL ISC 60 60 0.02 0.05 - - 0.02 0.08 - - 0.02 0.1 - - 75 75 - - - - - - - - - - - - - - dB V/V mA Common Mode Rejection (Vin = 0 to 5.0 V)
Power Supply Rejection Ratio VCC/VEE = 5.0 V/Ground to 3.0 V/Ground
AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A
Power Supply Current (Per Amplifier, VO = 0 V) VCC = 1.0 V VCC = 3.0 V VCC = 5.0 V VCC = 1.0 V (TA = -40 to 105C) VCC = 3.0 V (TA = -40 to 105C) VCC = 5.0 V (TA = -40 to 105C) ID mA - - - - - - 1.2 1.5 1.65 - - - 1.75 2.0 2.25 2.0 2.25 2.5 Output Short Circuit Current (Vin Diff = 1.0 V) VCC = 1.0 V Source Sink VCC = 3.0 V Source Sink VCC = 5.0 V Source Sink 6.0 10 15 40 20 40 13 13 32 64 40 70 26 26 60 140 140 140
MOTOROLA ANALOG IC DEVICE DATA
3
MC33502
AC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, TA = 25C, unless otherwise noted.)
AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AAA A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AAAA A AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAA A A A A AA A A A A AAAA A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A
Slew Rate (VS = 2.5 V, VO = -2.0 to 2.0 V, RL = 2.0 k, AV = 1.0) Positive Slope Negative Slope Unity Gain Bandwidth VCC = 1.0 V VCC = 3.0 V VCC = 5.0 V SR V/s 2.0 2.0 3.0 3.5 4.0 - - - - - - - - 3.0 3.0 4.0 4.5 5.0 6.5 60 6.0 6.0 6.0 7.0 8.0 - - - - - - - - BW MHz Gain Margin (RL =10 k, CL = 0 pF) Am m dB Phase Margin (RL = 10 k, CL = 0 pF) Deg dB Channel Separation (f = 1.0 Hz to 20 kHz, RL = 600 ) CS 120 200 Power Bandwidth (VO = 4.0 Vpp, RL = 1.0 k, THD 1.0%) BWP THD kHz % Total Harmonic Distortion (VO = 4.5 Vpp, RL = 600 , AV = 1.0) f = 1.0 kHz f = 10 kHz Differential Input Resistance (VCM = 0 V) 0.004 0.01 >1.0 2.0 Rin Cin en terra pF Differential Input Capacitance (VCM = 0 V) Equivalent Input Noise Voltage (VCC = 1.0 V, VCM = 0 V, VEE = Gnd, RS = 100 ) f = 1.0 kHz f = 10 kHz nV/Hz - - 30 60 - -
Characteristic
Symbol
Min
Typ
Max
Unit
Figure 1. Representative Block Diagram
VCC
IN-
IN+ Out
Offset Voltage Trim
VCC VCC Output Voltage Saturation Detector Clamp
VCC
Body Bias
4
MOTOROLA ANALOG IC DEVICE DATA
MC33502
GENERAL INFORMATION
The MC33502 dual operational amplifier is unique in its ability to provide 1.0 V rail-to-rail performance on both the input and output by using a SMARTMOS process. The amplifier output swings within 50 mV of both rails and is able to provide 50 mA of output drive current with a 5.0 V supply, and 10 mA with a 1.0 V supply. A 5.0 MHz bandwidth and a slew rate of 3.0 V/s is achieved with high speed depletion mode NMOS (DNMOS) and vertical PNP transistors. This device is characterized over a temperature range of -40C to 105C. Output Stage An additional feature of this device is an "on demand" base current cancellation amplifier. This feature provides base drive to the output power devices by making use of a buffer amplifier to perform a voltage-to-current conversion. This is done in direct proportion to the load conditions. This "on demand" feature allows these amplifiers to consume only a few micro-amps of current when the output stage is in its quiescent mode. Yet it provides high output current when required by the load. The rail-to-rail output stage current boost circuit provides 50 mA of output current with a 5.0 V supply (For a 1.0 V supply output stage will do 10 mA) enabling the operational amplifier to drive a 600 load. A buffer is necessary to isolate the load current effects in the output stage from the input stage. Because of the low voltage conditions, a DNMOS follower is used to provide an essentially zero voltage level shift. This buffer isolates any load current changes on the output stage from loading the input stage. A high speed vertical PNP transistor provides excellent frequency performance while sourcing current. The operational amplifier is also internally compensated to provide a phase margin of 60 degrees. It has a unity gain of 5.0 MHz with a 5.0 V supply and 4.0 MHz with a 1.0 V supply.
CIRCUIT INFORMATION
Input Stage One volt rail-to-rail performance is achieved in the MC33502 at the input by using a single pair of depletion mode NMOS devices (DNMOS) to form a differential amplifier with a very low input current of 40 fA. The normal input common mode range of a DNMOS device, with an ion implanted negative threshold, includes ground and relies on the body effect to dynamically shift the threshold to a positive value as the gates are moved from ground towards the positive supply. Because the device is manufactured in a p-well process, the body effect coefficient is sufficiently large to ensure that the input stage will remain substantually saturated when the inputs are at the positive rail. This also applies at very low supply voltages. The 1.0 V rail-to-rail input stage consists of a DNMOS differential amplifier, a folded cascode, and a low voltage balanced mirror. The low voltage cascoded balanced mirror provides high 1st stage gain and base current cancellation without sacrificing signal integrity. Also, the input offset voltage is trimmed to less than 1.0 mV because of the limited available supply voltage. The body voltage of the input DNMOS differential pair is internally trimmed to minimize the input offset voltage. A common mode feedback path is also employed to enable the offset voltage to track over the input common mode voltage. The total operational amplifier quiescent current drop is 1.3 mA/amp.
LOW VOLTAGE OPERATION
The MC33502 will operate at supply voltages from 0.9 to 7.0 V and ground. When using the MC33502 at supply voltages of less than 1.2 V, input offset voltage may increase slightly as the input signal swings within approximately 50 mV of the positive supply rail. This effect occurs only for supply voltages below 1.2 V, due to the input depletion mode MOSFETs starting to transition between the saturated to linear region, and should be considered when designing high side dc sensing applications operating at the positive supply rail. Since the device is rail-to-rail on both input and output, high dynamic range single battery cell applications are now possible.
MOTOROLA ANALOG IC DEVICE DATA
5
MC33502
Figure 2. Output Saturation versus Load Resistance
Vsat , OUTPUT SATURATION VOLTAGE (mV) Vsat , OUTPUT SATURATION VOLTAGE (V) 0 200 400 600 VCC 0 TA = -55C -0.5 -1.0 Source Saturation TA = 125C TA = 25C VCC
Figure 3. Drive Output Source/Sink Saturation Voltage versus Load Current
600 400 200 0 100 1.0 k VCC = 5.0 V VEE = 0 V RL to VCC/2 10 k 100 k 1.0 M
1.0 0.5 0
Sink Saturation VCC - VEE = 5.0 V 0 4.0 8.0 TA = -55C 12
TA = 25C
TA = 125C VEE
VEE 10 M
16
20
24
RL, LOAD RESISTANCE (k)
IO, OUTPUT CURRENT (mA)
Figure 4. Input Current versus Temperature
1000 100 I IB , INPUT CURRENT (pA) 80 A VOL, GAIN (dB) 10 1.0 0.1 0.01 100
Figure 5. Gain and Phase versus Frequency
m, EXCESS PHASE (DEGREES) 0 Gain Phase 60 40 20 0 1.0 VCC = 2.5 V VEE = -2.5 V RL = 10 k 10 100 1.0 k 10 k 100 k 1.0 M 10 M Phase Margin = 60 90 45
135 180
0.001 0 25 50 75 100 125
TA, AMBIENT TEMPERATURE (C)
f, FREQUENCY (Hz)
Figure 6. Transient Response
VCC = 0.5 V VEE = -0.5 V ACL = 1.0 CL = 10 pF RL = 10 k TA = 25C
Figure 7. Slew Rate
1.0 V/DIV (mV)
VCC = 2.5 V VEE = -2.5 V ACL = 1.0 CL = 10 pF RL = 600 TA = 25C
20 mV/DIV
t, TIME (500 s/DIV)
t, TIME (1.0 s/DIV)
6
MOTOROLA ANALOG IC DEVICE DATA
MC33502
Figure 8. Maximum Power Dissipation versus Temperature
1600 AVOL , OPEN LOOP GAIN (dB) 1400 1200 1000 800 600 400 200 0 -55 -25 0 25 50 75 100 125 SO-8 Pkg DIP Pkg 120 110 100 90 80 70 60 50 40 30 20 -55 VCC = 2.5 V VEE = -2.5 V RL = 600
PDmax, MAXIMUM POWER DISSIPATION (mW)
Figure 9. Open Loop Voltage Gain versus Temperature
-25
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (C)
TA, AMBIENT TEMPERATURE (C)
Figure 10. Output Voltage versus Frequency
7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 10 VCC = 2.5 V VEE = -2.5 V AV = 1.0 RL = 600 TA = 25C 100 1.0 k 10 k 100 k 1.0 M CMR, COMMON MODE REJECTION (dB) 8.0 VO, OUTPUT VOLTAGE (Vpp ) 120 100 80 60 40 20 0 10
Figure 11. Common Mode Rejection versus Frequency
VCC = 2.5 V VEE = -2.5 V TA = 25C 100 1.0 k 10 k 100 k 1.0 M
f, FREQUENCY (kHz)
f, FREQUENCY (kHz)
PSR, POWER SUPPLY REJECTION (dB)
140 120 100 80 60 40 20 0 10 100 1.0 k f, FREQUENCY (kHz) 10 k 100 k VCC = 0.5 V VEE = -0.5 V Either VCC or VEE TA = 25C VCC = 2.5 V VEE = -2.5 V
II SC I, OUTPUT SHORT CIRCUIT CURRENT (mA)
Figure 12. Power Supply Rejection versus Frequency
Figure 13. Output Short Circuit Current versus Output Voltage
100 80 60 40 Source 20 0 VCC = 2.5 V VEE = -2.5 V TA = 25C Sink
0
0.5
1.0
1.5
2.0
2.5
|VS| - |VO| (V)
MOTOROLA ANALOG IC DEVICE DATA
7
MC33502
Figure 14. Output Short Circuit Current versus Temperature
100 80 60 40 20 0 -55 VCC = 2.5 V VEE = -2.5 V Sink
II SC I, OUTPUT SHORT CIRCUIT CURRENT (mA)
ICC, SUPPLY CURRENT PER AMPLIFIER (mA)
Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load
2.5 2.0 1.5 TA = 125C
1.0 0.5 0 0 TA = 25C TA = -55C
Source
-25
0
25
50
75
100
125
0.5
1.0
1.5
2.0
2.5
TA, AMBIENT TEMPERATURE (C)
VCC, |VEE|, SUPPLY VOLTAGE (V)
Figure 16. Input Offset Voltage Temperature Coefficient Distribution
50 PERCENTAGE OF AMPLIFIERS (%) 40 30 20 10 0 -50 -40 VCC = 3.0 V VO = 1.5 V VEE = 0 V 60 Amplifiers Tested from 2 Wafer Lots PERCENTAGE OF AMPLIFIERS (%) 50 40 30 20 10
Figure 17. Input Offset Voltage Distribution
VCC = 3.0 V VO = 1.5 V VEE = 0 V TA = 25C 60 Amplifiers Tested from 2 Wafer Lots
-30
-20
-10
0
10
20
30
40
50
0 -5.0 -4.0 -3.0 -2.0
-1.0
0
1.0
2.0
3.0
4.0
5.0
TCVIO, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (V/C)
INPUT OFFSET VOLTAGE (mV)
Figure 18. Total Harmonic Distortion versus Frequency with 1.0 V Supply
THD, TOTAL HARMONIC DISTORTION (%) THD, TOTAL HARMONIC DISTORTION (%) 10 AV = 1000 1.0 AV = 100 AV = 10 AV = 1.0 0.01 Vout = 0.5 Vpp RL = 600 0.001 10 100 1.0 k f, FREQUENCY (Hz) VCC - VEE = 1.0 V 10 k 100 k 10
Figure 19. Total Harmonic Distortion versus Frequency with 5.0 V Supply
Vout = 0.4 Vpp RL = 600 1.0 AV = 1000 AV = 100 AV = 10 0.01 AV = 1.0 0.001 10 100 1.0 k f, FREQUENCY (Hz) VCC - VEE = 5.0 V 10 k 100 k
0.1
0.1
8
MOTOROLA ANALOG IC DEVICE DATA
MC33502
Figure 20. Slew Rate versus Temperature
VCC - VEE = 1.0 V + Slew Rate SR, SLEW RATE (V/ s) 3.0 VCC - VEE = 5.0 V + Slew Rate GBW, GAIN BANDWIDTH PRODUCT (MHz) 4.0 5.0 4.0 3.0 2.0 1.0 0 -55 VCC - VEE = 5.0 V f = 100 kHz
Figure 21. Gain Bandwidth Product versus Temperature
2.0 VCC - VEE = 1.0 V - Slew Rate 1.0
VCC - VEE = 5.0 V - Slew Rate
0 -55
-25
0
25
50
75
100
125
-25
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (C)
TA, AMBIENT TEMPERATURE (C)
Figure 22. Voltage Gain and Phase versus Frequency
60 40 AVOL, GAIN (dB) 20 0 RL = 600 CL = 0 TA = 25C 100 k 1.0 M f, FREQUENCY (Hz) 10 M VCC - VEE = 1.0 V VCC - VEE = 5.0 V m , PHASE MARGIN ( ) 80 60 VCC - VEE = 5.0 V VCC - VEE = 1.0 V 100
Figure 23. Gain and Phase Margin versus Temperature
100 VCC - VEE = 5.0 V RL = 600 CL = 100 pF 80 60 Phase Margin 40 20 0 -55 40 20 0 125
-20
Gain Margin -25 0 25 50 75 100
-40 10 k
TA, AMBIENT TEMPERATURE (C)
Figure 24. Gain and Phase Margin versus Differential Source Resistance
70 60 m , PHASE MARGIN ( ) 50 40 30 20 10 0 10 100 1.0 k Gain Margin VCC - VEE = 5.0 V RL = 600 CL = 100 pF TA = 25C Phase Margin 70 60 AV , GAIN MARGIN (dB) m , PHASE MARGIN ( ) 50 40 30 20 10 100 k 0 1.0 M 60 50 40 30 20
Figure 25. Feedback Loop Gain and Phase versus Capacitive Load
60 Phase Margin VCC - VEE = 5.0 V RL = 600 TA = 25C 50 40 30 20 Gain Margin 10 0 3.0 10 0 3000 AV , GAIN MARGIN (dB)
10 k
10
30
100
300
1000
RT, DIFFERENTIAL SOURCE RESISTANCE ()
CL, CAPACITIVE LOAD (pF)
MOTOROLA ANALOG IC DEVICE DATA
9
AV , GAIN MARGIN (dB)
MC33502
Figure 26. Channel Separation versus Frequency
120 CS, CHANNEL SEPARATION (dB) AV = 100 AV = 10 80 60 40 20 0 30 VCC - VEE = 5.0 V RL = 600 VO = 4.0 Vpp TA = 25C 100 300 10 k 30 k 100 k 300 k VO, OUTPUT VOLTAGE (Vpp ) 100 6.0 8.0 RL= 600 TA = 25C
Figure 27. Output Voltage Swing versus Supply Voltage
4.0
2.0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
f, FREQUENCY (Hz)
VCC, |VEE|, SUPPLY VOLTAGE (V)
en, EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz)
Figure 28. Equivalent Input Noise Voltage versus Frequency
70 60 50 40 30 20 10 0 10 100 1.0 k f, FREQUENCY (Hz) 10 k 100 k 0 VCC - VEE = 5.0 V TA = 25C 100 80 60 40 20
Figure 29. Gain and Phase Margin versus Supply Voltage
100 RL = 600 CL = 0 TA = 25C Phase Margin 80 60 40 20 0 0 1 2 3 4 5 6 7 VCC - VEE, SUPPLY VOLTAGE (V)
m , PHASE MARGIN ( )
Gain Margin
Figure 30. Useable Supply Voltage versus Temperature
VCC - VEE , USEABLE SUPPLY VOLTAGE (V) 1.6 A VOL , OPEN LOOP GAIN (dB) AVOL 10 dB RL = 600 120 100 80 60 40 20 0
Figure 31. Open Loop Gain versus Supply Voltage
1.2
0.8
0.4
RL = 600 TA = 25C 0 1.0 2.0 3.0 4.0 5.0 6.0
0 -55
-25
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (C)
VCC - VEE, SUPPLY VOLTAGE (V)
10
MOTOROLA ANALOG IC DEVICE DATA
A V , GAIN MARGIN (dB)
MC33502
Figure 32. 1.0 V Oscillator
RT 470 k
1.0 V CT 1.0 nF + - R1a 360 k FO 1.0 kHz 1.0 Vpp
R1b 360 k
R2 220 k
F O
+
2R C In TT
1
2(R1a R1b) R2
)
Figure 33. 1.0 V Voiceband Filter
C2 400 pF
Rf 100 k
0.5 V R2 10 k + - C1 80 nF -0.5 V R1 10 k Af VO
f
L
+
1 2pR1C1
[200 Hz
fL
fH
f
H
1 + 2pR C [4.0 kHz ff f 1)R R2
A
f
+
+11
MOTOROLA ANALOG IC DEVICE DATA
11
MC33502
Figure 34. Power Supply Application
15 V 5.0 V Vref 13 16 4
15 2 3 1
FB 22 k
11 MC34025 14
Output A Output B 4.7
4.7
5 6
8 12 10 7 9 0.1
470 pF
100 k 1.0 k + MC33502 - 3320 1.0 k
From Current Sense
Provides current sense amplification and eliminates leading edge spike.
Figure 35. 1.0 V Current Pump
IO IL 1.0 V VL R4 1.0 k RL 75 R5 2.4 k 8 7 4 + - 5 6 MC33502 R3 1.0 k R1 1.0 k VO
R2 3.3 k For best performance, use close tolerance resistors. IO/IL
IO 435 mA 212 mA
IL 463 A
-120 x 10-6 492 A
12
MOTOROLA ANALOG IC DEVICE DATA
MC33502
OUTLINE DIMENSIONS
P SUFFIX PLASTIC PACKAGE CASE 626-05 ISSUE K
8
5
-B-
1 4
NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040
F
NOTE 2
-A- L
C -T-
SEATING PLANE
J N D K
M
M
H
G 0.13 (0.005) TA
M
B
M
D SUFFIX PLASTIC PACKAGE CASE 751-06 (SO-8) ISSUE T A
8
D
5
C
E
1 4
H
0.25
M
B
M
h B C e A
SEATING PLANE
X 45 _
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_
q
L 0.10 A1 B 0.25
M
CB
S
A
S
q
MOTOROLA ANALOG IC DEVICE DATA
13
MC33502
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
14
MOTOROLA ANALOG IC DEVICE DATA
MC33502
Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 - http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shagawa-ku, Tokyo, Japan. 03-5487-8488
MOTOROLA ANALOG IC DEVICE DATA
MC33502/D 15

▲Up To Search▲

Price & Availability of MC33502

	To Download MC33502 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .